Testing of stainless steel by double yoke DC magnetometer

Research output: Contribution to journalArticle

1 Citation (Scopus)

Abstract

In the present work the microstructure and the strain induced phase transformation of Lean Duplex Stainless steel were studied. Sheet samples were cold rolled, the number of samples was nine; the applied deformation was up to 80%. The first magnetization curves and the saturation magnetization loops were measured by a double yoke DC magnetometer. The double yoke magnetometer is based on the former Stablein-Steinitz type magnet tester. The idea of the measuring set up was reconstructed and modernized at the Department of Materials Science and Engineering of BUTE. The obtained laboratory measuring device is an accurate closedcircuit DC magnetometer which widely can be used for testing bulk magnetic samples. The measuring set-up was found to be especially suitable for testing structural steel and hard magnetic samples. This equipment was successfully applied for studying the ferritic-martensitic phase transformation of lean duplex stainless steel due to cold rolling deformation.

Original languageEnglish
Pages (from-to)62-65
Number of pages4
JournalJournal of Electrical Engineering
Volume61
Issue number7 SUPPL
Publication statusPublished - 2013

Fingerprint

Magnetometers
Stainless steel
Testing
Phase transitions
Cold rolling
Materials science
Saturation magnetization
Magnets
Magnetization
Microstructure
Steel

Keywords

  • Double yoke DC magnetometer
  • Lean duplex stainless steel
  • Magnetic characterization
  • Phase transformation
  • Strain induced martensite

ASJC Scopus subject areas

  • Electrical and Electronic Engineering

Cite this

Testing of stainless steel by double yoke DC magnetometer. / Mészáros, I.

In: Journal of Electrical Engineering, Vol. 61, No. 7 SUPPL, 2013, p. 62-65.

Research output: Contribution to journalArticle

@article{c2f2be6792ac4fb8b659a36f7705be30,
title = "Testing of stainless steel by double yoke DC magnetometer",
abstract = "In the present work the microstructure and the strain induced phase transformation of Lean Duplex Stainless steel were studied. Sheet samples were cold rolled, the number of samples was nine; the applied deformation was up to 80{\%}. The first magnetization curves and the saturation magnetization loops were measured by a double yoke DC magnetometer. The double yoke magnetometer is based on the former Stablein-Steinitz type magnet tester. The idea of the measuring set up was reconstructed and modernized at the Department of Materials Science and Engineering of BUTE. The obtained laboratory measuring device is an accurate closedcircuit DC magnetometer which widely can be used for testing bulk magnetic samples. The measuring set-up was found to be especially suitable for testing structural steel and hard magnetic samples. This equipment was successfully applied for studying the ferritic-martensitic phase transformation of lean duplex stainless steel due to cold rolling deformation.",
keywords = "Double yoke DC magnetometer, Lean duplex stainless steel, Magnetic characterization, Phase transformation, Strain induced martensite",
author = "I. M{\'e}sz{\'a}ros",
year = "2013",
language = "English",
volume = "61",
pages = "62--65",
journal = "Journal of Electrical Engineering",
issn = "1335-3632",
publisher = "Slovenska Technicka Univerzita",
number = "7 SUPPL",

}

TY - JOUR

T1 - Testing of stainless steel by double yoke DC magnetometer

AU - Mészáros, I.

PY - 2013

Y1 - 2013

N2 - In the present work the microstructure and the strain induced phase transformation of Lean Duplex Stainless steel were studied. Sheet samples were cold rolled, the number of samples was nine; the applied deformation was up to 80%. The first magnetization curves and the saturation magnetization loops were measured by a double yoke DC magnetometer. The double yoke magnetometer is based on the former Stablein-Steinitz type magnet tester. The idea of the measuring set up was reconstructed and modernized at the Department of Materials Science and Engineering of BUTE. The obtained laboratory measuring device is an accurate closedcircuit DC magnetometer which widely can be used for testing bulk magnetic samples. The measuring set-up was found to be especially suitable for testing structural steel and hard magnetic samples. This equipment was successfully applied for studying the ferritic-martensitic phase transformation of lean duplex stainless steel due to cold rolling deformation.

AB - In the present work the microstructure and the strain induced phase transformation of Lean Duplex Stainless steel were studied. Sheet samples were cold rolled, the number of samples was nine; the applied deformation was up to 80%. The first magnetization curves and the saturation magnetization loops were measured by a double yoke DC magnetometer. The double yoke magnetometer is based on the former Stablein-Steinitz type magnet tester. The idea of the measuring set up was reconstructed and modernized at the Department of Materials Science and Engineering of BUTE. The obtained laboratory measuring device is an accurate closedcircuit DC magnetometer which widely can be used for testing bulk magnetic samples. The measuring set-up was found to be especially suitable for testing structural steel and hard magnetic samples. This equipment was successfully applied for studying the ferritic-martensitic phase transformation of lean duplex stainless steel due to cold rolling deformation.

KW - Double yoke DC magnetometer

KW - Lean duplex stainless steel

KW - Magnetic characterization

KW - Phase transformation

KW - Strain induced martensite

UR - http://www.scopus.com/inward/record.url?scp=84879158145&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84879158145&partnerID=8YFLogxK

M3 - Article

AN - SCOPUS:84879158145

VL - 61

SP - 62

EP - 65

JO - Journal of Electrical Engineering

JF - Journal of Electrical Engineering

SN - 1335-3632

IS - 7 SUPPL

ER -