Designed polyurethanes for potential biomedical and pharmaceutical applications: Novel synthetic strategy for preparing sucrose containing biocompatible and biodegradable polyurethane networks

Lajos Nagy, Miklós Nagy, Bence Vadkerti, L. Daróczi, G. Deák, M. Zsuga, S. Kéki

Research output: Contribution to journalArticle

1 Citation (Scopus)

Abstract

In this paper the preparation and detailed characterization of designed polyurethanes (SPURs) are reported for potential biological, biomedical and/or pharmaceutical applications. Importantly, in order to fulfill these goals all reactants and solvents used were selected according to the proposal of EUR-8 Pharmacopoeia. For the synthesis, a novel strategy was introduced and elaborated. Aseries ofSPURsamples was prepared frompoly(ε-caprolactone)-diol, 1,6-hexamethylene diisocyanate and sucrose as a chain extender/crosslinking agent to obtain sucrose containing polyurethanes. In addition, the mol ratios of the sucrose were varied within an order of magnitude. The prepolymers and the products of the syntheses were investigated by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) and infrared spectroscopy (IR), respectively. It was found that the reactivity of the eight free hydroxyl groups of sucrose are different, and after curing the SPUR samples at 60 °C no free isocyanate groups can be observed. Furthermore, swelling experiments performed with various solvents of different polarities revealed that the highest degree of swelling took place in dimethyl-sulfoxide. However, low degrees of swelling were recognized in water and hexane. It is important to note that the gel contents were around 90% in all cases, which demonstrate that the crosslinking was almost complete. In addition, the kinetics of swelling were also evaluated and successfully modeled. The crosslink densities were calculated from the data of the swelling experiments by means of the Flory-Rehner equation. Unexpectedly, it was found that the crosslink density decreased with the increasing sucrose content also in line with the results obtained by relaxation modulus experiments and dynamic mechanical analysis (DMA). The Tg and Tm of SPUR samples, determined from DSC and DMA measurements, were around -57 °C and 27 °C, respectively. According to the mechanical tests the SPUR samples showed high elongation at break values, i.e., high flexibilities. Furthermore, the stress-strain curves were also modeled and discussed.

Original languageEnglish
Article number825
JournalPolymers
Volume11
Issue number5
DOIs
Publication statusPublished - May 1 2019

Fingerprint

Polyurethanes
Sugar (sucrose)
Drug products
Swelling
Sucrose
Pharmaceutical Preparations
Dynamic mechanical analysis
Crosslinking
Isocyanates
Dimethyl sulfoxide
Experiments
Hexanes
Stress-strain curves
Dimethyl Sulfoxide
Hexane
Hydroxyl Radical
Ionization
Mass spectrometry
Curing
Elongation

Keywords

  • Mechanical testing
  • Poly(ε-caprolactone), 1,6-hexamethylene-diisocyanate
  • Polyurethane
  • Sucrose
  • Swelling

ASJC Scopus subject areas

  • Chemistry(all)
  • Polymers and Plastics

Cite this

@article{82b0830fda934e9fb612c440b3fc8780,
title = "Designed polyurethanes for potential biomedical and pharmaceutical applications: Novel synthetic strategy for preparing sucrose containing biocompatible and biodegradable polyurethane networks",
abstract = "In this paper the preparation and detailed characterization of designed polyurethanes (SPURs) are reported for potential biological, biomedical and/or pharmaceutical applications. Importantly, in order to fulfill these goals all reactants and solvents used were selected according to the proposal of EUR-8 Pharmacopoeia. For the synthesis, a novel strategy was introduced and elaborated. Aseries ofSPURsamples was prepared frompoly(ε-caprolactone)-diol, 1,6-hexamethylene diisocyanate and sucrose as a chain extender/crosslinking agent to obtain sucrose containing polyurethanes. In addition, the mol ratios of the sucrose were varied within an order of magnitude. The prepolymers and the products of the syntheses were investigated by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) and infrared spectroscopy (IR), respectively. It was found that the reactivity of the eight free hydroxyl groups of sucrose are different, and after curing the SPUR samples at 60 °C no free isocyanate groups can be observed. Furthermore, swelling experiments performed with various solvents of different polarities revealed that the highest degree of swelling took place in dimethyl-sulfoxide. However, low degrees of swelling were recognized in water and hexane. It is important to note that the gel contents were around 90{\%} in all cases, which demonstrate that the crosslinking was almost complete. In addition, the kinetics of swelling were also evaluated and successfully modeled. The crosslink densities were calculated from the data of the swelling experiments by means of the Flory-Rehner equation. Unexpectedly, it was found that the crosslink density decreased with the increasing sucrose content also in line with the results obtained by relaxation modulus experiments and dynamic mechanical analysis (DMA). The Tg and Tm of SPUR samples, determined from DSC and DMA measurements, were around -57 °C and 27 °C, respectively. According to the mechanical tests the SPUR samples showed high elongation at break values, i.e., high flexibilities. Furthermore, the stress-strain curves were also modeled and discussed.",
keywords = "Mechanical testing, Poly(ε-caprolactone), 1,6-hexamethylene-diisocyanate, Polyurethane, Sucrose, Swelling",
author = "Lajos Nagy and Mikl{\'o}s Nagy and Bence Vadkerti and L. Dar{\'o}czi and G. De{\'a}k and M. Zsuga and S. K{\'e}ki",
year = "2019",
month = "5",
day = "1",
doi = "10.3390/polym11050825",
language = "English",
volume = "11",
journal = "Polymers",
issn = "2073-4360",
publisher = "MDPI AG",
number = "5",

}

TY - JOUR

T1 - Designed polyurethanes for potential biomedical and pharmaceutical applications

T2 - Novel synthetic strategy for preparing sucrose containing biocompatible and biodegradable polyurethane networks

AU - Nagy, Lajos

AU - Nagy, Miklós

AU - Vadkerti, Bence

AU - Daróczi, L.

AU - Deák, G.

AU - Zsuga, M.

AU - Kéki, S.

PY - 2019/5/1

Y1 - 2019/5/1

N2 - In this paper the preparation and detailed characterization of designed polyurethanes (SPURs) are reported for potential biological, biomedical and/or pharmaceutical applications. Importantly, in order to fulfill these goals all reactants and solvents used were selected according to the proposal of EUR-8 Pharmacopoeia. For the synthesis, a novel strategy was introduced and elaborated. Aseries ofSPURsamples was prepared frompoly(ε-caprolactone)-diol, 1,6-hexamethylene diisocyanate and sucrose as a chain extender/crosslinking agent to obtain sucrose containing polyurethanes. In addition, the mol ratios of the sucrose were varied within an order of magnitude. The prepolymers and the products of the syntheses were investigated by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) and infrared spectroscopy (IR), respectively. It was found that the reactivity of the eight free hydroxyl groups of sucrose are different, and after curing the SPUR samples at 60 °C no free isocyanate groups can be observed. Furthermore, swelling experiments performed with various solvents of different polarities revealed that the highest degree of swelling took place in dimethyl-sulfoxide. However, low degrees of swelling were recognized in water and hexane. It is important to note that the gel contents were around 90% in all cases, which demonstrate that the crosslinking was almost complete. In addition, the kinetics of swelling were also evaluated and successfully modeled. The crosslink densities were calculated from the data of the swelling experiments by means of the Flory-Rehner equation. Unexpectedly, it was found that the crosslink density decreased with the increasing sucrose content also in line with the results obtained by relaxation modulus experiments and dynamic mechanical analysis (DMA). The Tg and Tm of SPUR samples, determined from DSC and DMA measurements, were around -57 °C and 27 °C, respectively. According to the mechanical tests the SPUR samples showed high elongation at break values, i.e., high flexibilities. Furthermore, the stress-strain curves were also modeled and discussed.

AB - In this paper the preparation and detailed characterization of designed polyurethanes (SPURs) are reported for potential biological, biomedical and/or pharmaceutical applications. Importantly, in order to fulfill these goals all reactants and solvents used were selected according to the proposal of EUR-8 Pharmacopoeia. For the synthesis, a novel strategy was introduced and elaborated. Aseries ofSPURsamples was prepared frompoly(ε-caprolactone)-diol, 1,6-hexamethylene diisocyanate and sucrose as a chain extender/crosslinking agent to obtain sucrose containing polyurethanes. In addition, the mol ratios of the sucrose were varied within an order of magnitude. The prepolymers and the products of the syntheses were investigated by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) and infrared spectroscopy (IR), respectively. It was found that the reactivity of the eight free hydroxyl groups of sucrose are different, and after curing the SPUR samples at 60 °C no free isocyanate groups can be observed. Furthermore, swelling experiments performed with various solvents of different polarities revealed that the highest degree of swelling took place in dimethyl-sulfoxide. However, low degrees of swelling were recognized in water and hexane. It is important to note that the gel contents were around 90% in all cases, which demonstrate that the crosslinking was almost complete. In addition, the kinetics of swelling were also evaluated and successfully modeled. The crosslink densities were calculated from the data of the swelling experiments by means of the Flory-Rehner equation. Unexpectedly, it was found that the crosslink density decreased with the increasing sucrose content also in line with the results obtained by relaxation modulus experiments and dynamic mechanical analysis (DMA). The Tg and Tm of SPUR samples, determined from DSC and DMA measurements, were around -57 °C and 27 °C, respectively. According to the mechanical tests the SPUR samples showed high elongation at break values, i.e., high flexibilities. Furthermore, the stress-strain curves were also modeled and discussed.

KW - Mechanical testing

KW - Poly(ε-caprolactone), 1,6-hexamethylene-diisocyanate

KW - Polyurethane

KW - Sucrose

KW - Swelling

UR - http://www.scopus.com/inward/record.url?scp=85066821056&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85066821056&partnerID=8YFLogxK

U2 - 10.3390/polym11050825

DO - 10.3390/polym11050825

M3 - Article

AN - SCOPUS:85066821056

VL - 11

JO - Polymers

JF - Polymers

SN - 2073-4360

IS - 5

M1 - 825

ER -