University of Miskolc

Research Output 1985 2019

Filter
Conference contribution
2017

A method for the determination of theoretical roughness in face milling considering the run-out of the inserts

Felho, C. & Kundrák, J., Jan 1 2017, Precision Machining IX - ICPM 2017. Trans Tech Publications Ltd, p. 251-258 8 p. (Solid State Phenomena; vol. 261 SSP).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

inserts
roughness
Surface roughness
Geometry
Surface topography
6 Citations (Scopus)

A new strategy in face milling - inverse cutting technology

Karpuschewski, B., Kundrák, J., Emmer, T. & Borysenko, D., Jan 1 2017, Precision Machining IX - ICPM 2017. Trans Tech Publications Ltd, p. 331-338 8 p. (Solid State Phenomena; vol. 261 SSP).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Milling (machining)
chips
flat surfaces
Boundary conditions
boundary conditions
8 Citations (Scopus)

Effects of technological parameters on surface characteristics in face milling

Varga, G. & Kundrák, J., Jan 1 2017, Precision Machining IX - ICPM 2017. Trans Tech Publications Ltd, p. 285-292 8 p. (Solid State Phenomena; vol. 261 SSP).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

flatness
Aluminum
surface roughness
manufacturing
examination
2016
2 Citations (Scopus)

Assessment of tool life and wear intensity of CBN tools in hard cutting

Kundrák, J., Markopoulos, A. P. & Makkai, T., 2016, Key Engineering Materials. Trans Tech Publications Ltd, Vol. 686. p. 1-6 6 p. (Key Engineering Materials; vol. 686).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Wear of materials
Machining
Bearings (structural)
Steel
Costs
5 Citations (Scopus)

Numerical investigation of the influence of tool rake angle on residual stresses in precision hard turning

Kundrák, J., Szabó, G. & Markopoulos, A. P., 2016, Key Engineering Materials. Trans Tech Publications Ltd, Vol. 686. p. 68-73 6 p. (Key Engineering Materials; vol. 686).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Residual stresses
Stainless Steel
Compressive stress
Life cycle
Machining

Surface roughness prediction in face milling by special tools

Felhö, C. & Kundrák, J., 2016, Key Engineering Materials. Trans Tech Publications Ltd, Vol. 686. p. 161-167 7 p. (Key Engineering Materials; vol. 686).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Surface roughness
Milling (machining)
Machining
Geometry
Experiments
2015
23 Citations (Scopus)

Surface roughness modelling in face milling

Felho, C., Karpuschewski, B. & Kundrák, J., 2015, Procedia CIRP. Elsevier, Vol. 31. p. 136-141 6 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Surface roughness
Experiments
2014
1 Citation (Scopus)

A method to estimate interfacial energy between eutectic solid phases from the results of eutectic solidification experiments

Kaptay, G., 2014, Materials Science Forum. Trans Tech Publications Ltd, Vol. 790-791. p. 133-139 7 p. (Materials Science Forum; vol. 790-791).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

interfacial energy
Interfacial energy
eutectics
Eutectics
solidification
18 Citations (Scopus)

Comparison of theoretical and real surface roughness in face milling with octagonal and circular inserts

Felho, C. & Kundrák, J., 2014, Key Engineering Materials. Vol. 581. p. 360-365 6 p. (Key Engineering Materials; vol. 581).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Surface roughness
Metal cutting
Analytical models
Experiments
3 Citations (Scopus)

Determination of the chip width and the undeformed chip thickness in rotational turning

Sztankovics, I. & Kundrák, J., 2014, Key Engineering Materials. Vol. 581. p. 131-136 6 p. (Key Engineering Materials; vol. 581).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Kinematics
7 Citations (Scopus)

Investigation of residual stresses in case of hard turning of case hardened 16MnCr5 Steel

Szabo, G. & Kundrák, J., 2014, Key Engineering Materials. Vol. 581. p. 501-504 4 p. (Key Engineering Materials; vol. 581).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Steel
Residual stresses
Finite element method
2013

Microstructure, corrosion and wear resistance evaluation of aluminium matrix composites reinforced by TiC and WC nanoparticles

Karantzalis, A. E., Lekatou, A., Evangelou, A., Gousia, V., Miskaki, C., Sfikas, A. K., Sioulas, D., Gacsi, Z., Baumli, P., Kaptay, G. & Simon, A., 2013, Engineering Against Failure - Proceedings of the 3rd International Conference of Engineering Against Failure, ICEAF 2013. University of Patras, Laboratory of Technology and Strength of Materials, p. 214-222 9 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Wetting agents
Wear resistance
Corrosion resistance
Casting
Wear of materials
2012
19 Citations (Scopus)

Characterization of topography of cut surface based on theoretical roughness indexes

Felho, C. & Kundrák, J., 2012, Key Engineering Materials. Vol. 496. p. 194-199 6 p. (Key Engineering Materials; vol. 496).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Topography
Surface roughness
Planning
Surface properties
Geometry
6 Citations (Scopus)

Numerical research of the plastic strain in hard turning in case of orthogonal cutting

Szabó, G. & Kundrák, J., 2012, Key Engineering Materials. Vol. 496. p. 162-167 6 p. (Key Engineering Materials; vol. 496).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Plastic deformation
Finite element method
Steel
Experiments
21 Citations (Scopus)

Possibility of reducing environmental load in hard machining

Kundrák, J. & Varga, G., 2012, Key Engineering Materials. Vol. 496. p. 205-210 6 p. (Key Engineering Materials; vol. 496).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Machining
Production engineering
Coolants
Lubricants
Metals
2011

Extraction of pure copper by electrowinning from spent chloride PCB etching solutions

Kulcsar, T. & Kékesi, T., 2011, Proceedings - European Metallurgical Conference, EMC 2011. Vol. 5. p. 1868-1869 2 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Electrowinning
Polychlorinated Biphenyls
Polychlorinated biphenyls
Chlorides
Copper
2010
3 Citations (Scopus)

Diffusion of carbon in the centerline region of continuous cast slabs

Reger, M., Vero, B., Kardos, I., Fábián, E. R. & Kaptay, G., 2010, Materials Science Forum. Vol. 659. p. 441-446 6 p. (Materials Science Forum; vol. 659).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Alloying elements
casts
slabs
Carbon
Sandwich structures
2008

Aluminium salts hydrolysis products from industrial anodising sludges in wastewater treatment

Chambino, T., Correia, A. & Barany, S., 2008, Progress in Colloid and Polymer Science. Vol. 135. p. 65-69 5 p. (Progress in Colloid and Polymer Science; vol. 135).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

sludge
Land fill
Aluminum
Wastewater treatment
hydrolysis
1 Citation (Scopus)

Strength of flocs formed from aluminium sulfate hydrolysis product particles

Mészáros, R. & Bárány, S., 2008, Progress in Colloid and Polymer Science. Vol. 135. p. 70-76 7 p. (Progress in Colloid and Polymer Science; vol. 135).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

hydrolysis
sulfates
Hydrolysis
Alkalinity
Hydration
2007
41 Citations (Scopus)

Comparison of different theoretical models to experimental data on viscosity of binary liquid alloys

Budai, I., Benko, M. Z. & Kaptay, G., 2007, Materials Science Forum. Vol. 537-538. p. 489-496 8 p. (Materials Science Forum; vol. 537-538).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Viscosity
Viscosity of liquids
Liquids
Temperature
2 Citations (Scopus)

On the wettability, encapsulation and surface phase transition in monotectic liquid metallic systems

Kaptay, G., 2007, Materials Science Forum. Vol. 537-538. p. 527-532 6 p. (Materials Science Forum; vol. 537-538).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Liquid metals
Encapsulation
Wetting
Phase transitions
Liquids

The evolution of materials engineering education in Miskolc

Gacsi, Z. & Kékesi, T., 2007, Proceedings of SEFI and IGIP Joint Annual Conference 2007: Joining Forces in Engineering Educations Towards Excellence. University of Miskolc, p. 305-306 2 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Engineering education
engineering
education
2006

A clean method applying anion-exchange separation and membrane-electrolysis to regenerate Fe-Zn-HCl spent pickling liquors

Csicsovszki, G., Kékesi, T. & Törók, T. I., 2006, TMS Annual Meeting. Vol. 2006. p. 427-436 10 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Pickling
Electrolysis
Anions
electrokinesis
ion exchange
24 Citations (Scopus)

On the temperature gradient induced interfacial gradient force, acting on precipitated liquid droplets in monotectic liquid alloys

Kaptay, G., 2006, Materials Science Forum. Vol. 508. p. 269-274 6 p. (Materials Science Forum; vol. 508).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Thermal gradients
Interfacial energy
Liquids
Emulsions
Temperature
2 Citations (Scopus)

Surface quality of hard turned bore holes

Kundrák, J., Osanna, P. H., Afjehi-Sadat, A. & Bana, V., 2006, 18th IMEKO World Congress 2006: Metrology for a Sustainable Development. Vol. 2. p. 1044-1049 6 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Surface properties
Roughness measurement
Boring
Surface measurement
Wear resistance
2003
2 Citations (Scopus)

Anion-exchange separations in HCL media for the ultra-high purification of cobalt

Kékesi, T., Uchikoshi, M., Mimura, K. & Isshiki, M., 2003, Yazawa International Symposium: Metallurgical and Materials Processing: Principles and Techologies; Aqueous and Electrochemical Processing. Kongoli, F., Itagaki, K., Yamauchi, C., Sohn, H. Y., Kongoli, F., Itagaki, K., Yamauchi, C. & Sohn, H. Y. (eds.). Vol. 3. p. 211-225 15 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Purification
Cobalt
Ion exchange
Negative ions
Impurities
2000
3 Citations (Scopus)

On the drag force acting on ceramic particles during processing of cast MMCs

Kaptay, G. & Kelemen, K. K., 2000, Proceedings of the TMS Fall Meeting. Rothatgi, P. K. (ed.). p. 45-60 16 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Drag
Processing
Liquid metals
Volume fraction
Sedimentation
4 Citations (Scopus)

Ultra-high purification of transition metals by anion exchange applying various oxidation states

Kékesi, T., Uchikoshi, M., Mimura, K., Zhu, Y. & Isshiki, M., 2000, Proceedings of the Second International Conference on Processing Materials for Properties. Mishra, B., Yamauchi, C., Mishra, B. & Yamauchi, C. (eds.). p. 979-984 6 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Transition metals
Purification
Ion exchange
Negative ions
Sorption
1994

Grinding of tool materials of high hardness

Kundrák, J., Lovei, P. & Szabo, Z., 1994, Proc Jt Hung Br Int Mechatronics Conf. p. 71-76 6 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Hardness
Cermets
Machining
Mechanical properties
Experiments
1993
5 Citations (Scopus)

Purification of copper chloride solution by anion exchange for the preparation of ultra high purity copper

Kékesi, T., Mimura, K. & Isshiki, M., 1993, First International Conference on Processing Materials for Properties. Publ by Minerals, Metals & Materials Soc (TMS), p. 565-568 4 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Purification
Ion exchange
Negative ions
Copper
Impurities
1990
1 Citation (Scopus)

Development and production of non-metallurgical aluminas in Hungary

Csige, J., Matyasi, J., Toth Benjaminne, M. & Kaptay, G., 1990, Light Metals 1990. Publ by Minerals, Metals & Materials Soc (TMS), p. 121-129 9 p.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Alumina
Aluminum
Oxides